ANTIFUSE PROGRAMMING FPGAS PDF

FPGA (Field Programmable Gate Array) is an integrated circuit FPGA devices are produced by a number of semiconductor basic modes of programming: Antifuse-based FPGAs are different from the previous ones in that they can be. That is where the Field Programmable Gate Arrays (FPGAs) become of interest! They are hardware The antifuse programming technology is the simplest one. ❖The Programming technology. ❖The basic logic cells. ❖The I/O logic cells. ❖ Programmable interconnect. ❖Software to design and program the FPGA.

Author: Malkree Kazishakar
Country: Fiji
Language: English (Spanish)
Genre: Spiritual
Published (Last): 15 January 2016
Pages: 238
PDF File Size: 11.27 Mb
ePub File Size: 11.78 Mb
ISBN: 723-6-61772-694-6
Downloads: 61261
Price: Free* [*Free Regsitration Required]
Uploader: Vudokasa

In this way, the failed lamp was bypassed and illumination restored to the rest of the street.

Their disadvantage, however, is lower area efficiency compared to other types. May Learn how and when to remove this template message. When the bulb blows, the entire mains voltage is applied across the single blown lamp. A specialized structure optimized for the purpose can be employed where the antifuse is an integral part of the design.

Antifuses may be fgas in programmable read-only memory PROM. As the number of bonding pads is limited for a given size of the chip, various multiplexing strategies are used for larger number of antifuses.

Antifuse – Wikipedia

QuickLogic Corporation refers to their antifuses as “ViaLinks” because blown fuses create a connection between two crossing layers of wiring on the chip in the same way that a via on a printed circuit board creates a connection between copper layers.

They are historically used especially with bipolar processes, where the thin oxide needed for dielectric antifuses is not available. Zener diodes can be used as antifuses. Dielectric antifuses employ a very thin oxide barrier between a pair of conductors. This programming, performed after manufacturing, is permanent and irreversible. From Wikipedia, the free encyclopedia. Because the series string would be rendered inoperable by a single lamp failing, each bulb has an antifuse installed within it.

The antifuse is made using wire with a high resistance coating and this wire is coiled over the two vertical filament support wires inside the bulb. The antifuse is usually triggered using an approximately 5 mA current. Views Read Edit View history. The terminals of the antifuses are usually accessible as bonding pads and the trimming process is performed before wire-bonding and encapsulating the chip. When a sufficiently high voltage is applied across the amorphous silicon it is turned into a polycrystalline silicon-metal alloy with a low resistancewhich is conductive.

  HISTIOCITOSIS DE CELULAS DE LANGERHANS EN NIOS PDF

The p-n junction that serves as such diode is overloaded with a current spike and overheated. Antifuses are widely used to permanently program integrated circuits ICs. Unlike Christmas lights, the circuit usually contained an automatic device to regulate the electric current flowing in the circuit, preventing the current from rising as additional lamps burned out.

Also circuits built via the antifuse’s permanent conductive paths may be faster than similar circuits implemented in PLDs using SRAM technology. With a poly-diffusion antifuse, the high current density creates heatwhich melts a thin insulating layer between polysilicon and diffusion electrodes, creating a permanent resistive silicon link.

For example a precision resistor can be manufactured by forming several series resistors with Zeners in parallel oriented to be nonconductive during normal operation of the device and then shorting selected Zeners to shunt the unwanted resistors. Retrieved from ” https: Unsourced material may be challenged and removed.

This page was last edited on 7 Julyat Articles needing additional references from May All articles needing additional references. Amorphous silicon is a material usually not used in either bipolar or CMOS processes and requires an additional manufacturing step. By this approach, it is possible only to lower the value of the resulting resistor. It is therefore necessary to shift the manufacturing tolerances so that the lowest-value typically made is equal to or larger than the desired value.

A standard NPN transistor structure is often used in common bipolar processes as the antifuse.

An antifuse is an electrical device that performs the opposite function to a fuse. Each individual street-lamp was equipped with a film cutout ; a small disk of insulating film that separated two contacts connected to the two wires leading to the lamp. Often a special bulb with no antifuse and often a slightly different rating so it blows first as the voltage peogramming too high known as a “fuse bulb” is incorporated into the string of lights to protect against the possibility of severe overcurrent if too many bulbs fail.

This article needs additional citations for verification. This rapidly causes the antifuse to short out the blown bulb, allowing the series circuit to resume functioning, albeit with a larger proportion of the mains voltage now applied to each of the remaining lamps. Each bit contains both a fuse and an antifuse and is programmed by triggering one of the two.

  CLIVE CUSSLER PLAGUE SHIP PDF

Zener zap is frequently employed in mixed-signal circuits for trimming values of analog porgramming.

The resulting resistance of the junction is in the range of 10 ohms. In a similar fashion to that of Christmas tree lights, before the advent of high-intensity discharge lampsstreet light circuits using incandescent light bulbs were often operated as high-voltage series circuits.

In some cases a combined circuit with zeners and transistors can be used to form a zapping matrix; with additional zeners, the trimming which uses voltages higher than the normal operational voltage of the chip can be performed even after packaging the chip.

The parallel resistors cannot have too low value as that would sink the zapping current; a series-parallel combination of resistors and antifuses is employed in such cases. Formation of the conductive channel is performed by a dielectric breakdown forced by a high voltage pulse. This technology has many applications. They may be less susceptible to alpha particles which can cause circuits to malfunction.

Please help improve this article by adding citations to reliable sources. Whereas a fuse starts with a low resistance and is designed to permanently break an electrically conductive path typically when the current through the path exceeds a specified limitan antifuse starts with a high resistance and is designed to permanently create an electrically conductive path typically when the voltage across the antifuse exceeds a certain level.

FPGAs in computer

The larger, traditional, C7 and C9 style lights are wired in parallel and are rated to operate directly at mains voltage. Ordinarily for operation from mains voltagesthe lamps are wired in series. In the same fashion as with the Christmas lights described above, if the lamp failed, the entire voltage of the street lighting circuit thousands of volts was imposed across the insulating film in the cutout, causing it to rupture.

The insulation of the antifuse wire withstands the ordinary low voltage imposed across a functioning lamp but rapidly breaks down under the full mains voltage, giving the antifuse action.